I see a few dealers offering Crosman bolts with hold open magnets. Searching the web I came across this site. You can buy either the cylinder type magnets (drill hole and insert), or disc type that you could glue to the back of the bolt.
https://www.kjmagnetics.com/products.asp?cat=13 (https://www.kjmagnetics.com/products.asp?cat=13)
https://www.kjmagnetics.com/products.asp?cat=10 (https://www.kjmagnetics.com/products.asp?cat=10)
I purchased 50ea of 3mm x 1.5mm round Neo magnets (same that Don Cothran uses in his bolts) from ebay for $3.99 with free shipping. I only needed a couple of them but hey, the deal was sweet.
I did that once to a bolt and was veyr happy with the end result. Charles Mellon claims you need only magnetize a bolt by running it over a magnet to get a similar result. Never tried it.
I've wondered if that would work too Chef. There isn't a lot of weight so it wouldn't take much magnetic energy.
I have some scraps of samarium cobalt magnets, I'll try it later on.
Ordered a few disc and cylinder magnets from them to try out. Well see how they work out.
Inquiring minds want to know. Keep us posted.
Got em yesterday. They are some powerful little magnets. The biggest challenge was trying to drill a straight 1/8" hole in a 1/4" bolt with a hand drill >:( Installed 2 cylinder mags (1/8 X 1/4) in two of my bolts and glued a disc mag (1/8 X 1/32) on the other. They all worked great :-*
Nicely done. AS. I think all bolts should have magnets installed in the back. It just makes sense.
Thanks for the link - just ordered some since I'll be pulling "the stapler" apart to install the new trigger assy.
JMJ
Quote from: JMJinNC on June 21, 2013, 04:34:28 PM
Thanks for the link - just ordered some since I'll be pulling "the stapler" apart to install the new trigger assy.
JMJ
Methinks someone has a 1701P grip frame/trigger group.
Quote from: breakfastchef on June 21, 2013, 05:00:23 PM
Methinks someone has a 1701P grip frame/trigger group.
:-*
So probably dumb questions...
For the magnet mod to work, you need to have a steel rear cap on the breech, right?
The magnet surface would be what makes contact with the hammer pin when cocking?
You have to be careful that the hammer pin never hits the bolt/magnet when firing when the hammer slams forward and hits the valve pin. I had one that would hit the rear of the bolt at the end of the stroke. Neodymium magnets tend to chip and break when struck by anything.
Quote from: breakfastchef on June 15, 2013, 10:31:01 PM
I did that once to a bolt and was veyr happy with the end result. Charles Mellon claims you need only magnetize a bolt by running it over a magnet to get a similar result. Never tried it.
Yes, that works too. But it's not pertinent. You can also magnetize screwdrivers and hex keys with this: http://www.magnetsource.com/Consumer%20Pages/Mag_Demag.html (http://www.magnetsource.com/Consumer%20Pages/Mag_Demag.html)
The magnet gets mounted on the bolt, which is held against the vertical pin on the hammer after cocking the gun (hammer held by sear). This holds the bolt open for pellet loading. Otherwise it can (and will) slide forward if the gun is held muzzle-down.
I'm pretty sure there is no contact at all between the hammer pin and the bolt when firing.
JMJ
Quote from: Colt25 on June 21, 2013, 09:49:43 PM
Yes, that works too. But it's not pertinent. You can also magnetize screwdrivers and hex keys with this: http://www.magnetsource.com/Consumer%20Pages/Mag_Demag.html (http://www.magnetsource.com/Consumer%20Pages/Mag_Demag.html)
Great link! I bookmarked it. Good prices too, I didn't check shipping yet though.